MicroChip Pic 18F452 microcontroller
and Mplab C18 student edition c compiler for pic 18f series
would like to do some projects here
pc serial to pic 3 axis stepper
finally got something moving with on pc signgo vinylcutting software
pic 18f452 stepper motor plotter
18f452_stepper_plotter.WMV
The code i used pstep_new_version_001.zip
a plot done on the pic 18f452 plotter
A1 size still no errors larger possible
A0 size 1100mm wide smile
at 0,006mm/step
= 183,333 steppulses
think it can go upto -8,388,608 to +8,388,607
and further if changed short long integer to long integer
dot matrix lcd module(hd44780 lcd controller) 2x16 2x20 etcetera
external lcd functions mplab => xlcd.h
using a parallel interface 4 or 8bit
pic18f452 & lcd module for 3phase ac motor frequency regulator inverter external display
inverter outputs a analog voltage wicht is translated to a human readable output on the dot matrix display in volt hertz or rpm
pic18f452 & lcd module for binary input => error display output
PLC ouputs a 8 bit error the display converts it to a human readable error
all low cost & low component count
after a day of puzzle and blank screen
finally got something on the lcd screen
more details will come later
changed/edited => c:\mcc18\h\xlcd.h
to 4bit data lower nibble portc and 3control_bits rs rw en on portd
launch/run/compile/build => c:\mcc18\src\traditional\makeonep18f242.bat 18f452
mistakes i made:
saw 15,16=back led for pin1,2 because of wierd pinout LCD 15,16,1,2, =>14
forget to set LCD contrast voltage
compiler complained about a few things in my source
config decl
some info i have to place
Simplified Configuration Bits Support
The configuration bits syntax has now been built-in to the compiler, to allow for easy setting of these values. Instead of custom romdata sections or the CONFIG_DECL macro, a simple elegant syntax is supported. For
example:
#pragma config OSC = HS
#pragma config WDT = OFF
#pragma config LVP = OFF
The compiler will even print a list of available configuration bits when the --help-config command-line option is given. For example:
> mcc18 --help-config -p=18f452
Configuration settings available for processor 18F452
Oscillator Selection:
OSC = LP LP
OSC = XT XT
OSC = HS HS
OSC = RC RC
OSC = EC EC-OSC2 as Clock Out
OSC = ECIO EC-OSC2 as RA6
OSC = HSPLL HS-PLL Enabled
OSC = RCIO RC-OSC2 as RA6
Osc. Switch Enable:
OSCS = ON Enabled
OSCS = OFF Disabled
...
Damn OERR overflow error => Help me?
Changed to a 11.0592 x4 PLL for a nicer zero error SPBRG val
A bit overclocked 40Mhz PIC => 44.236.800Hz
something that puzzles me
plotter cutter blade steering arc compensation
so that the cutter will produce sharp corners
the drag knive does not follow the movement exactly
so its shopping off corners
the swivel drag knife cutterblade steering arc
swivel compensation
have you ever thought about that
http://www.luberth.com/help/vinyl_cutter_offset_path_1mm.html
Hmmm => ProCutZ+: Schneidesoftware mit Offsetkompensation ...
so there is software out there
I DO NOT LIKE THE PROCUTZ software
there is also letscut www.lets.de also do not like it
easycut says it does blade steering radius compensation and software looks good
pitty there is no working demo
P-Step &CStep® ©Copyright 2003-2004 Luberth Dijkman Bangert 23 Andijk The Netherlands Europe
This page was last modified:
